Water Balancing Guide
Establishing and keeping the correct water balance is important for a number of reasons:
- Chemical efficiency
- Bather comfort
- Protection of pool and plant room equipment
- Water quality and appearance
- Makes it easier and less time consuming to look after the pool Some people believe that keeping the right pH is all that is needed to achieve the correct water balance, this isn’t the case and although pH is important there are other factors that also need to be considered. In the table below we have illustrated the properties that make up water balance and the ideal levels that should be maintained.
Ideal Pool water Levels
| Calcium Hardness | Total Alkalinity | pH | Total Dissolved Solids |
|---|---|---|---|
| 200 - 275mg/l | 80 - 150ml/l | 7.2 - 7.6 | Less than 1,500mg/l |
pH
pH is a measure of how acidic or how alkaline (not to be confused with total alkalinity) the water is.
The pH scale ranges between 0 to 14, with 0 being very acidic and 14 very alkaline. pH 7 is neutral and for pools the pH should be maintained between 7.2 and 7.6, this being slightly alkaline protects the pool and plant room equipment from aggressive, corrosive water and is comfortable for bathers.
Problems Associated with Incorrect pH Levels
| pH below 7.2 | pH above 7.6 |
|---|---|
| Corrosive Water | Scale Formation |
| Etching of surfaces | Filter Calcification |
| Staining | Cloudy Water |
| Skin & Eye Irritation | Drying to Skin |
| Damage to plant equipment | Reduced effectiveness of chlorine |
If the pH of your pool water is either low or high it should be corrected using Purisan pH Plus or Purisan pH Minus, respectively. The table below will help you calculate the dose rate to suit your pool (24 hours after dosing re-check & repeat if required).
| Pool Volume | pH Plus (To Increase pH) | pH Minus (to lower pH) | |
|---|---|---|---|
| Litres | Gallons | Dose Rate | Dose Rate |
| 4,546 | 1,000 | 50g | 50g |
| 11,365 | 2,500 | 125g | 125g |
| 22,730 | 5,000 | 250g | 250g |
| 45,460 | 10,000 | 500g | 500g |
Calcium Hardness
Calcium hardness is the measure of how hard or soft the water is. The level will vary depending on where your water supply comes from, for example in some parts of Scotland the water is very soft and in parts of Kent the water can be very hard. The hardness depends upon the amount of mineral salts (mainly calcium) that are dissolved in the water and the more salts there are the harder the water is.
Problems Associated with Incorrect Calcium Hardness Levels
| Low Calcium Hardness Less than 200mg/l | High Calcium Hardness More than 200mg/l |
|---|---|
| Corrosive water | Scale formation |
| Etching of surface | Filter calcification |
| Staining | Cloudy Water |
| Foam | Lower sanitiser effectiveness |
If the calcium hardness of your pool water is less than 200mg/l then it should be increased using Purisan Calcium Hardness Increaser, details of dose rates can be found below:
| Pool Volume | To Increase Calcium Hardness by | |||
|---|---|---|---|---|
| Litres | Gallons | 10mg/l | 25mg/l | 50mg/l |
| 4,546 | 1,000 | 68g | 170g | 340g |
| 11,365 | 2,500 | 170g | 425g | 850g |
| 22,730 | 5,000 | 340g | 850g | 1700g |
| 45,460 | 10,000 | 680g | 1700g | 3400g |
If the calcium hardness of your pool water is greater than 275mg/l then Lo-Chlor Multi Stain remover (followed by a maintenance dose of Lo-Chlor No More Metal) should be used. Stain and Scale Inhibitor works by helping the pool water keep the minerals in solution thus preventing them from precipitating out and causing scale deposits (which are then more easily removed by the filter). Our Cu-Lator range of sequestrants can also be used in the prevention of dissolved metals. Multi-Stain Remover Dose Rates -
| Pool Volume | Dose | |
|---|---|---|
| Gallons | Litres | |
| 5,500 | 25,000 | 500g |
| 11,000 | 50,000 | 1000g |
| 16,500 | 75,000 | 1500g |
Total Alkalinity
Total alkalinity is a measurement of the waters ability to resist pH change. If the total alkalinity is low then the pH can fluctuate making it difficult to control and maintain at the ideal level. If the total alkalinity is high then the pH can be difficult to change and will keep rising. A high total alkalinity can also lead to the formation of a bicarbonate scale on pool surfaces, within pipework and in plant room equipment.
If the total alkalinity of your pool water is below 80mg/l it should be increased using Purisan TA Raiser, Dose Rates -
| Pool Volume | To Increase Total Alkalinity by | |||
|---|---|---|---|---|
| Litres | Gallons | 10mg/l | 25mg/l | 50mg/l |
| 4,546 | 1,000 | 81g | 203g | 405g |
| 11,365 | 2,500 | 203g | 508g | 1.01Kg |
| 22,730 | 5,000 | 405g | 1010g | 2020g |
| 45,460 | 10,000 | 810g | 2020g | 4050g |
If the total alkalinity of your pool water is above 150mg/l then Purisan TA Reducer can be used to lower it.
| Pool Volume | To Reduce Total Alkalinity | |||
|---|---|---|---|---|
| Litres | Gallons | Dose Rate | ||
| 4,546 | 1,000 | 50g | ||
| 11,365 | 2,500 | 125g | ||
| 22,730 | 5,000 | 250g | ||
| 45,460 | 10,000 | 500g | ||
Chlorine Stabiliser
One of the major reasons for chlorine loss from swimming pools is that it is drawn out of the pool by the UV rays of the sun. Adding chlorine stabiliser to an outdoor pool at the start of the swimming season will substantially reduce the amount of chlorine lost to sunlight, saving you money. Many of the chlorine donors used to treat the pool water already contain stabiliser, we would therefore recommend that you test the level before adding any more. The ideal chlorine stabiliser level is 40mg/l, if the level in your pool is less than this use Purisan Stabiliser Granules to increase it. If the chlorine stabiliser level is greater than 200mg/l it is time to drain some of the existing pool water out of the pool and top it up with some fresh water to lower the level. As with T.D.S. levels, frequent top ups with fresh water due to regular backwashing will help to keep the chlorine stabiliser level from rising too high. Remember that water balance can change with dilution, so keep checking the levels throughout the swimming season.
| Pool Volume | To Increase Stabiliser Levels by | |||
|---|---|---|---|---|
| Litres | Gallons | 10mg/l | 25mg/l | 50mg/l |
| 4,546 | 1,000 | 45g | 113g | 271g |
| 11,365 | 2,500 | 113g | 283g | 678g |
| 22,730 | 5,000 | 225g | 563g | 1360g |
| 45,460 | 10,000 | 450g | 1120g | 2710g |
Total Dissolved Solids (T.D.S.)
T.D.S. is, as the name suggests, the sum of everything that is dissolved in the water including, minerals, chemicals and debris. The maximum recommended T.D.S. level is 1,500mg/l, when the level rises above this it is time to do some dilution, by removing some of the old pool water and adding some fresh.
High T.D.S. levels can cause poor chemical efficiency and increase consumption together with dull looking water that may taste salty.
Regular backwashing of the filter as mentioned on page 3 will mean that your pool will need topping up with fresh water fairly often, this will help keep the T.D.S. level under control and reduce the need to drain down and refill.